#VIRTUALBOX NETWORK SETTINGS MAC ADDRESS PC#
#VIRTUALBOX NETWORK SETTINGS MAC ADDRESS LICENSE#

After that, simply buy a license to export data to remote storage devices and use the application whenever you want. RX bytes:1799 (1.7 KB) TX bytes:7023 (7.After searching for the data and mounting the file, you always have the opportunity to see amazing results for free. TX packets:55 errors:0 dropped:0 overruns:0 carrier:0 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:66 errors:0 dropped:0 overruns:0 carrier:0 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:58 errors:0 dropped:0 overruns:0 carrier:0 RX packets:5 errors:0 dropped:0 overruns:0 frame:0 Network configuration on Guest (Ubuntu) after Network Interface Setting I can see a new interface are created as shown below.

#VIRTUALBOX NETWORK SETTINGS MAC ADDRESS PC#

Then check ifconfig on the Virtual PC (Ubuntu in VirtualBox in my case). Network configuration on Host (Windows 10) after Network Interface SettingĮthernet adapter VirtualBox Host-Only Network:ĭescription. I can find a new interface is added as shown below.

First, check the ipconfig on the host PC (Windows 10 PC in my case). Now let's check if the new interface is successfully set. In this case, check the network adapter settings in the host PC (Windows 10 PC in my case) and make it sure you find 'VirtualBox Host-Only Network' and it is 'Enabled' as shown below. NOTE : In some case, you may not see the item in 'Attached to' drop down box in the above configuration. Default setting for Adapter 3 is as follows.Ĭonfigure the settings for Adapter 3 as shown below and click. So I will configure Adapter 3 for the new interface between Host PC and Virtual PC. Click on button as shown below.Īs shown in previous section, Adapter 1 and Adapter 2 are used for the default Network Interface for my PC. Now let's setup a Network Interface between the Host PC and Virtual PC. You would know this is for enp0s8 by comparing MAC address with HWaddr shown above.

You would know this is for enp0s3 by comparing MAC address with HWaddr shown above.įollowing shows the interface setting for enp0s3. These two interface configuration can be seen in Vitural Box Network Setting as shown below.įollowing shows the interface setting for enp0s3. RX bytes:37042 (37.0 KB) TX bytes:37042 (37.0 KB)Įxcept the local loopback interface lo, you see there are two network interface named epn0s3 and epn0s8. TX packets:368 errors:0 dropped:0 overruns:0 carrier:0 RX packets:368 errors:0 dropped:0 overruns:0 frame:0 TX packets:352 errors:0 dropped:0 overruns:0 carrier:0 RX packets:48 errors:0 dropped:0 overruns:0 frame:0 TX packets:6220 errors:0 dropped:0 overruns:0 carrier:0 RX packets:9533 errors:0 dropped:0 overruns:0 frame:0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Network configuration on Guest (Ubuntu) before Network Interface SettingĮnp0s3 Link encap:Ethernet HWaddr 08:00:27:d5:84:25 This would be different from what you see in your PC. : Enabledįollowing is the network configuration I get on my Virtual PC (Ubuntu in Virtual Box). : Saturday, Febru3:58:48 PMĭefault Gateway. Wireless LAN adapter Local Area Connection* 2:ĭescription. : Intel(R) Ethernet Connection (4) I219-LM Network configuration on Host (Windows 10) before Network Interface Setting This will be different from what you see on your PC. Of course, this is just for your reference.

Following is the configuration on my PC before setting the interface. Take a look at the network configuration of your Host PC.

Virtualbox network settings mac address